jump to navigation

STAC5 – NEW Lower Price for Microstepping Drive March 18, 2014

Posted by Servo2Go.com in New Product Press Releases.
Tags: , , , , , , ,
trackback

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply, and features…      

  • High performance
  • Built-in power supply & regeneration clamp
  • 120 and 220 VAC models
  • Accepts pulse & direction, streaming commands, stored programming
  • 10/100 MBit Ethernet & EtherNet/IP
  • Advanced anti-resonance
  • Matching high performance motors
AMP's STAC5 Microstep Driver with HT23 Motor

AMP’s STAC5 Microstep Driver with HT23 Motor

The STAC5 provides up to 5 amps per phase from a high bus voltage with sophisticated current control, delivering high torque over a board range of speeds.  An advanced anti-resonance algorithm with electronic damping allows for maximum torque utilization and fast settling times.

The STAC5 is available in 120VAC and 220VAC versions, both housed in a compact package.

All STAC5 models include 100Mbit Ethernet communication.  The Ethernet interface is used to configure the STAC5 and motor, and also supports the SCL and Q languages over standard Ethernet cabling, addressing and protocols.There are 3 control options available with the STAC5 stepper drives: S, Q and IP.

  • “S” drives can operate in pulse & direction, velocity, and streaming serial (SCL) control modes.  To select the control mode, as well as to setup the motor and configure other drive parameters, use the ST Configurator™ software.
  • “Q” drives can operate in all of the same control modes as an S drive, plus they have the ability to run stand-alone Q programs stored in non-volatile memory.  Q programs are created using the Q Programmer™ software, which provides multi-tasking, math functions, conditional processing, data register manipulation, and more features in a robust yet simple text-based programming language.  Like S drives, Q drives must first be setup and configured using the ST Configurator™ software.
  • “IP” drives come with built-in EtherNet/IP network communications, the widely used industrial protocol for manufacturing automation applications.  With EtherNet/IP users can control, configure and query the drive using an open, standards-based, industrial Ethernet connection at speeds up to 100 MBits/sec.  The STAC5-IP drives run all of the same control modes as STAC5-Q drives, with the addition that all drive features can be accessed over EtherNet/IP, including more than 100 commands and 130 registers for controlling motion, I/O, configuration, polling, math, register manipulation, and Q programming.  STAC5-IP drives are setup and configured using ST Configurator™, and Q programs are created using Q Programmer™.

An encoder feedback option provides position verification, stall detection and/or stall prevention.  Applied Motion’s proprietary stall prevention algorithm monitors rotor lag and automatically reduces speed or acceleration to avoid motor stalls, allowing 100% torque utilization.

The STAC5 can be purchased with a wide range of high torque step motors, optimized for use with the drive.  Three lengths of HT23 are available in single and double shaft configurations:  HT23-552, HT23-553 and HT23-554, with holding torque ranging from 84 to 255 ounce-inches.  Three lengths of HT34 are also available in single and double shaft configurations:  HT34-495, HT34-496 and HT34-497, with holding torque ranging from 550 to 1700 ounce-inches.

For more information on the STAC5 Stepper Drives from Applied Motion Products, click on the link below:

https://www.servo2go.com/product.php?ID=105241&cat=

For more information, please contact:

Editorial Contact:

Warren Osak
sales@servo2go.com
Toll Free Phone:  877-378-0240
Toll Free Fax:       877-378-0249
www.servo2go.com

Tags:  Step Drive, Stepper Driver, Step Driver, Step Motor, Automation, Motion Control, Servo2Go, Applied Motion Products

Advertisements

Comments»

No comments yet — be the first.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: